Tony Sarendal | 1 May 01:07 2004

Re: to scrub or not to scrub

On Wed, Apr 28, 2004 at 07:42:30AM +0400, Toxa wrote:
> Hello Peter,
> 
> Wednesday, April 28, 2004, 3:13:53 AM, you wrote:
> 
> 
> PH> Not all fragmented packets are evil.
> 
> 
> Practically, very-very little percent of normal traffic is fragmented
> for any reason. At least in my network. So personally I see no sense
> to waste resources for packet reassembling.  It's suits me fine but
> maybe not suit  anyone else.
> 

SNMP.
If anyone wonders why the cisco interface descriptions don't show
up in cricket/mrtg/whatever, stop dropping fragments.

/Tony S

Paulo Jorge Correia Pires | 1 May 01:29 2004
Picon

Re: wireless auth+crypto

i've said something simple to the client side, and authpf 
means an ssh session and i do not want ppl to have shell 
access to the AP/AR! but thanks for the tip.

well i'm sorry if the question bothers u. thnks anyways
bye

On Fri, 30 Apr 2004 17:28:55 -0500
  Simon Lundström <simon <at> metawire.org> wrote:
>authpf
>
>On Fri, Apr 30, 2004 at 10:59:01PM +0100, Paulo Jorge 
>Correia Pires wrote:
>> hi there!
>> 
>> i'm implementing a WLAN covering my entire village and 
>>i'm 
>> using OpenBSD and Prism cards as AP/AR (access 
>> points/routers). Everything is fine! Now i'm looking for 
>>a 
>> authentication and traffic-encryptation solution, 
>>perhaps 
>> some accounting too. I'm aware and experienced with 
>> technologies as radius and IPSec, but on this i could 

>>only 
>> find an rfc (freeradius.org).
>> i want to authenticate users on a captive portal and 
>>store 
>> them on a simple backend like some DBMS (MySQL, 
(Continue reading)

Peter Bristow | 1 May 01:58 2004
Picon

slimp()

Hi, I've been reading some code and seen the use of splimp(), not knowing 
quite what this did I ran to the man pages and found spl (9) though it 
does not appear on this page. Some searches on marc found that it was a 
priority just above splvm, but noone detailed quite what it did. I was 
hoping someone could clarify quite what it did. 

Sorry if I have missed anything obvious. 

Thanks for any help

Pete 

Todd Boyer | 1 May 02:49 2004

Re: CF card install

Check out man pages for installboot, disklabel, fdisk, and newfs 

Setup a host machine with a complete OpenBSD install on it.  Attach a CF
reader and card to the USB port.  Mount the drive and tar or dump the OS

-Todd

-----Original Message-----
From: owner-misc <at> openbsd.org [mailto:owner-misc <at> openbsd.org] On Behalf
Of Tom Geman
Sent: Friday, April 30, 2004 6:11 PM
To: misc <at> openbsd.org
Subject: CF card install

I am trying to install OpenBSD 3.5 on a 1GB CF card directly.

The problem I am having is that when I get to the partioning stage of
the install, my CF card only allows me yo user about 40-50 mb, and I
don't know why.  Do I have to do something to prepare the card for
installation?  Can I not install directly to the CF card like you can
for a hard drive?

The card is recognized as a 1GB card in the dmesg.

I have attached a hard drive and installed openbsd 3.5 on it just so I
could get the dmesg and disklabel of the card.  I have attached the
dmesg of the system running with a 120GB hard disk at wd0 and the CF
card at wd1. Please note the system I am aiming for will not have the
hard drive 
attached,
(Continue reading)

Greg Thomas | 1 May 03:16 2004

Re: winxp to obsd ipsec vpn tunnel setup guide

Simon Dassow
> On Fri, 2004-04-30 at 22:29, vxla <at> nxio.us wrote:
>> On Fri, 2004-04-30 at 11:16:10 -0700, Jack Berger proclaimed...
>>
>> > A number of times I've seen ppl ask about a guide for
>> > setting up an IPsec VPN tunnel between a Windows
>> > machine and an OpenBSD machine.
> [...]
>> > It was mentioned on undeadly recently and I
>> > think it is very helpful.
>>
>> Are you a troll? Be honest, now.
>
> I don't think so.
>
>> How in the world does this apply to OpenBSD?
>
> In the world where OpenBSD is the VPN endpoint and Winblows is the
> client.
> Always good to see documentation that makes our life easier.
>
> So who's the troll now?
>

A link directly to one of the PDFs probably would have been clearer.

Greg

Martin Holzhauer | 1 May 03:30 2004
Picon
Picon

Install Problems with Adaptec AHA-2940 (DMESG incl.)

I have a Pentium 90 with a Adaptec AHA-2940 and tried 2 hours ago to
install 3.5 stable.

This is a DMESG from the Debian system on this mashine
because i cant moutn the oBSD Disk an thas my only system
with a floppy drive

<snip>

Linux version 2.2.20-compact (herbert <at> gondolin) (gcc version 2.7.2.3) #1
Sat Apr 20 12:40:22 EST 2002
BIOS-provided physical RAM map:
 BIOS-e820: 0009f000  <at>  00000000 (usable)
 BIOS-e820: 03f00000  <at>  00100000 (usable)
Detected 90206 kHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 179.81 BogoMIPS
Memory: 62616k/65536k available (1452k kernel code, 416k reserved, 928k
data, 124k init)
Dentry hash table entries: 8192 (order 4, 64k)
Buffer cache hash table entries: 65536 (order 6, 256k)
Page cache hash table entries: 16384 (order 4, 64k)
CPU: Intel Pentium 75 - 200 stepping 01
Checking 386/387 coupling... Hmm, FPU using exception 16 error reporting
with FDIV bug.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
Intel Pentium with F0 0F bug - workaround enabled.
POSIX conformance testing by UNIFIX
PCI: PCI BIOS revision 2.10 entry at 0xf13d0
(Continue reading)

Theo de Raadt | 1 May 03:38 2004
Picon

Re: Install Problems with Adaptec AHA-2940 (DMESG incl.)

You do not tell us what boot media you used.  Some boot media contains
ahc(4) support -- others do not.

> I have a Pentium 90 with a Adaptec AHA-2940 and tried 2 hours ago to
> install 3.5 stable.
...
> oBSD reports during the install
> 	"Adaptec AHA-2940" rev 0x00 at pci0 dev14 function 0 not configured
> and
> 	No Disks found

Martin Holzhauer | 1 May 03:41 2004
Picon
Picon

Install Problems with Adaptec AHA-2940 (DMESG incl.)

I have a Pentium 90 with a Adaptec AHA-2940 and tried 2 hours ago
toinstall 3.5 stable.

This is a DMESG from the Debian system on this mashinebecause i cant
moutn the oBSD Disk an thas my only systemwith a floppy drive

<snip>
Linux version 2.2.20-compact (herbert <at> gondolin) (gcc version 2.7.2.3) #1
Sat Apr 20 12:40:22 EST 2002
BIOS-provided physical RAM map:
 BIOS-e820: 0009f000  <at>  00000000 (usable)
 BIOS-e820: 03f00000  <at>  00100000 (usable)
Detected 90206 kHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 179.81 BogoMIPS
Memory: 62616k/65536k available (1452k kernel code, 416k reserved, 928k
data, 124k init)
Dentry hash table entries: 8192 (order 4, 64k)
Buffer cache hash table entries: 65536 (order 6, 256k)
Page cache hash table entries: 16384 (order 4, 64k)
CPU: Intel Pentium 75 - 200 stepping 01
Checking 386/387 coupling... Hmm, FPU using exception 16 error reporting
with FDIV bug.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
Intel Pentium with F0 0F bug - workaround enabled.
POSIX conformance testing by UNIFIX
PCI: PCI BIOS revision 2.10 entry at 0xf13d0
PCI: Using configuration type 2
PCI: Probing PCI hardware
(Continue reading)

Martin Holzhauer | 1 May 03:48 2004
Picon
Picon

Re: Install Problems with Adaptec AHA-2940 (DMESG incl.)

Am Sa, den 01.05.2004 schrieb Theo de Raadt um 03:38:
> You do not tell us what boot media you used.  Some boot media contains
> ahc(4) support -- others do not.
> 
> > I have a Pentium 90 with a Adaptec AHA-2940 and tried 2 hours ago to
> > install 3.5 stable.
> ...
> > oBSD reports during the install
> > 	"Adaptec AHA-2940" rev 0x00 at pci0 dev14 function 0 not configured
> > and
> > 	No Disks found
> 

i tested with floppyB35 and floppyC35 both with the same error

Nick Holland | 1 May 03:55 2004
Picon

Re: Install Problems with Adaptec AHA-2940 (DMESG incl.)

Martin Holzhauer wrote:
> 
> Am Sa, den 01.05.2004 schrieb Theo de Raadt um 03:38:
> > You do not tell us what boot media you used.  Some boot media contains
> > ahc(4) support -- others do not.
> >
> > > I have a Pentium 90 with a Adaptec AHA-2940 and tried 2 hours ago to
> > > install 3.5 stable.
> > ...
> > > oBSD reports during the install
> > >     "Adaptec AHA-2940" rev 0x00 at pci0 dev14 function 0 not configured
> > > and
> > >     No Disks found
> >
> 
> i tested with floppyB35 and floppyC35 both with the same error

AND THAT'S YOUR PROBLEM.

http://www.openbsd.org/i386.html
Read it.  Carefully.

http://www.openbsd.org/faq/faq4.html#getdmesg
will tell you how to get a useful dmesg here.  You can include a
windows control pannel screen shot for as relevant as a Linux dmesg is
to us for this.

Nick.
--

-- 
http://www.holland-consulting.net
(Continue reading)


Gmane