I need some help ?

Re: I need some help ?

Fri, Mar 14, 2003 at 09:50:53AM -0000, Otchere, Kofi:
> Hello,
>  
> I need some help in adding more commands in the script that runs on the
> router and the switch.  Also, is it possible to use Cisco Pix?

Currently, bin/rancid will have to be modified to do this.

there are is a hash and an array that have to be modified.

%commands=(
        'show version'          => "ShowVersion",
        'show redundancy secondary'             => "ShowRedundancy",
		...

this associates a command with a filtering routine.

 <at> commands=(
        "show version",
        "show redundancy secondary",
		...

this establishes the order in which commands are executed.

(unknown)

Hello,

I've just installed Rancid on a Linux BOX, and when i am doing the do-diffs
i have a problem with some CISCO commands not listed in the IOS:

=====================================
Getting missed routers: round 4.
ir00.pul.lsn.lb0.ch.vtxnet.net: missed cmd(s): show bootvar,dir /all
sup-microcode:,show boot,show vlan,dir /all slot0:,show c7200,show
module,dir /all slot1:,write term,dir /all sup-bootflash:,dir /all
nvram:,dir /all slot2:,show diag,show controllers cbus,show env all,dir /all
disk0:,dir /all disk1:,show vtp status,dir /all disk2:,show gsr chassis,show
variables boot,show controllers,dir /all bootflash:,show diagbus,show
flash,show install active
ir00.pul.lsn.lb0.ch.vtxnet.net: End of run not found
!ROM Bootstrap: Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

Is there any possibilities to disable these commands ? Or is it working
anyway ?

Regards,

Nicolas

----------------------------------------
STRINA Nicolas
IP Network Engineer
VTX Services - Internet Service Provider
Av. de Lavaux, 101 CH-1009 Pully
nicolas.strina <at> smart-telecom.ch
http://www.vtx.ch
----------------------------------------

RE:

Unsupported commands are not a big deal.  The 'End of run not found' is
not good however.

Set 'NOPIPE=YES; export NOPIPE' in <rancid dir>/bin/env.  Then run
do-diffs.  A file will be created with the exact output form rancid.
The file will be called <router name>.raw  Review this file to determine
why there is not a 'end' to the 'write term' command.

Hope this helps,
Joe

-----Original Message-----
From: Strina Nicolas [mailto:nicolas.strina <at> smart-telecom.ch] 
Sent: Wednesday, March 26, 2003 2:45 AM
To: rancid-discuss <at> shrubbery.net
Subject: 

Hello,

I've just installed Rancid on a Linux BOX, and when i am doing the
do-diffs
i have a problem with some CISCO commands not listed in the IOS:

=====================================
Getting missed routers: round 4.
ir00.pul.lsn.lb0.ch.vtxnet.net: missed cmd(s): show bootvar,dir /all
sup-microcode:,show boot,show vlan,dir /all slot0:,show c7200,show
module,dir /all slot1:,write term,dir /all sup-bootflash:,dir /all
nvram:,dir /all slot2:,show diag,show controllers cbus,show env all,dir
/all
disk0:,dir /all disk1:,show vtp status,dir /all disk2:,show gsr
chassis,show
variables boot,show controllers,dir /all bootflash:,show diagbus,show
flash,show install active
ir00.pul.lsn.lb0.ch.vtxnet.net: End of run not found
!ROM Bootstrap: Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE
(fc1)

Is there any possibilities to disable these commands ? Or is it working
anyway ?

Regards,

Nicolas

----------------------------------------
STRINA Nicolas
IP Network Engineer
VTX Services - Internet Service Provider
Av. de Lavaux, 101 CH-1009 Pully
nicolas.strina <at> smart-telecom.ch
http://www.vtx.ch
----------------------------------------

Re:

Wed, Mar 26, 2003 at 05:10:01AM -0800, Rizzo, Joe:
> Unsupported commands are not a big deal.  The 'End of run not found' is
> not good however.
> 
> Set 'NOPIPE=YES; export NOPIPE' in <rancid dir>/bin/env.  Then run
> do-diffs.  A file will be created with the exact output form rancid.
> The file will be called <router name>.raw  Review this file to determine
> why there is not a 'end' to the 'write term' command.
> 
> Hope this helps,
> Joe

you also need to specify the '-d' option to rancid, else this file
will be deleter.

another useful data-point is what appears at the end of the <router name>.new
file.  this will provide clues as to what command's output and maybe what
within that output caused the heart-burn.

given the first command in the missed list is show bootvar, i suspect it
is 'show boot' that triggered it.  what o/p do you get from this command?

> -----Original Message-----
> From: Strina Nicolas [mailto:nicolas.strina <at> smart-telecom.ch] 
> Sent: Wednesday, March 26, 2003 2:45 AM
> To: rancid-discuss <at> shrubbery.net
> Subject: 
> 
> Hello,
> 
> I've just installed Rancid on a Linux BOX, and when i am doing the
> do-diffs
> i have a problem with some CISCO commands not listed in the IOS:
> 
> =====================================
> Getting missed routers: round 4.
> ir00.pul.lsn.lb0.ch.vtxnet.net: missed cmd(s): show bootvar,dir /all
> sup-microcode:,show boot,show vlan,dir /all slot0:,show c7200,show
> module,dir /all slot1:,write term,dir /all sup-bootflash:,dir /all
> nvram:,dir /all slot2:,show diag,show controllers cbus,show env all,dir
> /all
> disk0:,dir /all disk1:,show vtp status,dir /all disk2:,show gsr
> chassis,show
> variables boot,show controllers,dir /all bootflash:,show diagbus,show
> flash,show install active
> ir00.pul.lsn.lb0.ch.vtxnet.net: End of run not found
> !ROM Bootstrap: Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE
> (fc1)
> 
> Is there any possibilities to disable these commands ? Or is it working
> anyway ?
> 
> Regards,
> 
> Nicolas
> 
> ----------------------------------------
> STRINA Nicolas
> IP Network Engineer
> VTX Services - Internet Service Provider
> Av. de Lavaux, 101 CH-1009 Pully
> nicolas.strina <at> smart-telecom.ch
> http://www.vtx.ch
> ----------------------------------------
>