headers
Christian Franke | 2 May 2011 21:41
Picon
Favicon

Re: scteHD204UI on ICH10R in RAID5

Fabian Geis wrote:
> Hi!
>
> I try to build a RAID 5 array on an ASUS P5QD Turbo with ICH10R. The HD204UI
> work quite well when not in RAID but in AHCI mode and I can set scterc to 70
> as needed. Ah, it is running on an Win 2008 R2 host.
>
> Two problems: When creating a RAID 5 array I can still access the drives
> individually with smartctl via /dev/csmiX,X but the set parameter turns out
> to be 57345 now. I can still set the sctecr again to 70 - no error message,
> but if I check it again it's still 37345.
>    

The SCT ERC Get command requires ATA output registers from SMART WRITE 
LOG command which might not be supported by all drivers. The ERC Set 
command does not need output registers, so Set might work while Get doesn't.

Intel RAID version? "smartctl -l scterc" worked for me with Intel RAID 
5.5 and 8.8.

Does "smartctl -H" work properly? This command also requires ATA output 
registers.

> What to do? Ignore and believe it's still 70? I fear of the devices dropping
> out of the array. Maybe it's not set correctly, maybe it's just a problem of
> reading the value when in RAID and it actually IS 70. When I delete the RAID
> volume and check the disks individually it IS 70.
>    

Which driver was used after deleting the RAID: Still Intel RAID driver
(Continue reading)

Permalink | Reply | 1 comment |
headers
Peter Radig | 8 May 2011 17:58
Picon

Kernel errors on Solaris 11 x64 after moving from 5.39 to 5.40

My box has 21 SATA disks, some of them directly connected to the motherboard, others via LSI 3081E-R.

OS is Solaris Express 11 x64 (2010.11 SRU5).

 

Doing a “smartctl -d sat -a /dev/rdsk/c7t12d0” with smartmontools 5.39 on any of the disks delivers the expected output and no kernel warning.

 

However, with 5.40 and everything else unchanged I get:

 

May  8 17:55:01 rocky scsi: [ID 107833 kern.warning] WARNING: /pci <at> 0,0/pci8086,2e21 <at> 1/pci1000,3140 <at> 0/sd <at> c,0 (sd7):

May  8 17:55:01 rocky   Error for Command: <undecoded cmd 0x85>    Error Level: Recovered

May  8 17:55:01 rocky scsi: [ID 107833 kern.notice]     Requested Block: 0                         Error Block: 0

May  8 17:55:01 rocky scsi: [ID 107833 kern.notice]     Vendor: ATA                                Serial Number:       MN1220

May  8 17:55:01 rocky scsi: [ID 107833 kern.notice]     Sense Key: Soft_Error

May  8 17:55:01 rocky scsi: [ID 107833 kern.notice]     ASC: 0x0 (<vendor unique code 0x0>), ASCQ: 0x1d, FRU: 0x0

 

or (on another disk):

 

May  8 17:31:39 rocky scsi: [ID 107833 kern.warning] WARNING: /pci <at> 0,0/pci1043,82d4 <at> 1f,2/disk <at> 3,0 (sd3):

May  8 17:31:39 rocky   Error for Command: <undecoded cmd 0xa1>    Error Level: Recovered

May  8 17:31:39 rocky scsi: [ID 107833 kern.notice]     Requested Block: 0                         Error Block: 0

May  8 17:31:39 rocky scsi: [ID 107833 kern.notice]     Vendor: ATA                                Serial Number:            

May  8 17:31:39 rocky scsi: [ID 107833 kern.notice]     Sense Key: Soft_Error

May  8 17:31:39 rocky scsi: [ID 107833 kern.notice]     ASC: 0x0 (no additional sense info), ASCQ: 0x0, FRU: 0x0

 

How can I avoid these warnings (which reappear every 30 minutes from smartd)?

------------------------------------------------------------------------------
WhatsUp Gold - Download Free Network Management Software
The most intuitive, comprehensive, and cost-effective network 
management toolset available today.  Delivers lowest initial 
acquisition cost and overall TCO of any competing solution.
http://p.sf.net/sfu/whatsupgold-sd
_______________________________________________
Smartmontools-support mailing list
Smartmontools-support <at> lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/smartmontools-support
Permalink | Reply | 8 comments |
headers
Christian Franke | 8 May 2011 21:54
Picon
Favicon

Re: Kernel errors on Solaris 11 x64 after moving from 5.39 to 5.40

Peter Radig wrote:
>
> My box has 21 SATA disks, some of them directly connected to the 
> motherboard, others via LSI 3081E-R.
>
> OS is Solaris Express 11 x64 (2010.11 SRU5).
>
> Doing a “smartctl -d sat -a /dev/rdsk/c7t12d0” with smartmontools 5.39 
> on any of the disks delivers the expected output and no kernel warning.
>
> However, with 5.40 and everything else unchanged I get:
>
> May 8 17:55:01 rocky scsi: [ID 107833 kern.warning] WARNING: 
> /pci <at> 0,0/pci8086,2e21 <at> 1/pci1000,3140 <at> 0/sd <at> c,0 (sd7):
>
> May 8 17:55:01 rocky Error for Command: <undecoded cmd 0x85> Error 
> Level: Recovered
>
> May 8 17:55:01 rocky scsi: [ID 107833 kern.notice] Requested Block: 0 
> Error Block: 0
>
> May 8 17:55:01 rocky scsi: [ID 107833 kern.notice] Vendor: ATA Serial 
> Number: MN1220
>
> May 8 17:55:01 rocky scsi: [ID 107833 kern.notice] Sense Key: Soft_Error
>
> May 8 17:55:01 rocky scsi: [ID 107833 kern.notice] ASC: 0x0 (<vendor 
> unique code 0x0>), ASCQ: 0x1d, FRU: 0x0
>
> or (on another disk):
>
> May 8 17:31:39 rocky scsi: [ID 107833 kern.warning] WARNING: 
> /pci <at> 0,0/pci1043,82d4 <at> 1f,2/disk <at> 3,0 (sd3):
>
> May 8 17:31:39 rocky Error for Command: <undecoded cmd 0xa1> Error 
> Level: Recovered
>
> May 8 17:31:39 rocky scsi: [ID 107833 kern.notice] Requested Block: 0 
> Error Block: 0
>
> May 8 17:31:39 rocky scsi: [ID 107833 kern.notice] Vendor: ATA Serial 
> Number:
>
> May 8 17:31:39 rocky scsi: [ID 107833 kern.notice] Sense Key: Soft_Error
>
> May 8 17:31:39 rocky scsi: [ID 107833 kern.notice] ASC: 0x0 (no 
> additional sense info), ASCQ: 0x0, FRU: 0x0
>
> How can I avoid these warnings (which reappear every 30 minutes from 
> smartd)?
>
>    

The solaris specific code was not changed between 5.39 and 5.40. The 
commands 0x85 and 0xa1 are the 16 and 12 byte versions of SAT ATA 
PASS-THROUGH 16 and 12 which are used to for all ATA commands if '-d 
sat' is specified.

"smartctl -a" is equivalent to "smartctl -H -i -c -A -l error -l 
selftest -l selective". Please try which of those options produce a 
kernel warning.

Thanks,
Christian

------------------------------------------------------------------------------
WhatsUp Gold - Download Free Network Management Software
The most intuitive, comprehensive, and cost-effective network 
management toolset available today.  Delivers lowest initial 
acquisition cost and overall TCO of any competing solution.
http://p.sf.net/sfu/whatsupgold-sd
Permalink | Reply | 7 comments |
headers
Peter Radig | 8 May 2011 22:04
Picon

Re: Kernel errors on Solaris 11 x64 after moving from 5.39 to 5.40

It's the "-H" that causes the grief.

Thanks,
Peter

-----Original Message-----
From: Christian Franke [mailto:Christian.Franke <at> t-online.de] 
Sent: 08 May, 2011 21:54
To: Peter Radig
Cc: smartmontools-support <at> lists.sourceforge.net
Subject: Re: [smartmontools-support] Kernel errors on Solaris 11 x64 after moving from 5.39 to 5.40

Peter Radig wrote:
>
> My box has 21 SATA disks, some of them directly connected to the 
> motherboard, others via LSI 3081E-R.
>
> OS is Solaris Express 11 x64 (2010.11 SRU5).
>
> Doing a "smartctl -d sat -a /dev/rdsk/c7t12d0" with smartmontools 5.39 
> on any of the disks delivers the expected output and no kernel warning.
>
> However, with 5.40 and everything else unchanged I get:
>
> May 8 17:55:01 rocky scsi: [ID 107833 kern.warning] WARNING: 
> /pci <at> 0,0/pci8086,2e21 <at> 1/pci1000,3140 <at> 0/sd <at> c,0 (sd7):
>
> May 8 17:55:01 rocky Error for Command: <undecoded cmd 0x85> Error
> Level: Recovered
>
> May 8 17:55:01 rocky scsi: [ID 107833 kern.notice] Requested Block: 0 
> Error Block: 0
>
> May 8 17:55:01 rocky scsi: [ID 107833 kern.notice] Vendor: ATA Serial
> Number: MN1220
>
> May 8 17:55:01 rocky scsi: [ID 107833 kern.notice] Sense Key: 
> Soft_Error
>
> May 8 17:55:01 rocky scsi: [ID 107833 kern.notice] ASC: 0x0 (<vendor 
> unique code 0x0>), ASCQ: 0x1d, FRU: 0x0
>
> or (on another disk):
>
> May 8 17:31:39 rocky scsi: [ID 107833 kern.warning] WARNING: 
> /pci <at> 0,0/pci1043,82d4 <at> 1f,2/disk <at> 3,0 (sd3):
>
> May 8 17:31:39 rocky Error for Command: <undecoded cmd 0xa1> Error
> Level: Recovered
>
> May 8 17:31:39 rocky scsi: [ID 107833 kern.notice] Requested Block: 0 
> Error Block: 0
>
> May 8 17:31:39 rocky scsi: [ID 107833 kern.notice] Vendor: ATA Serial
> Number:
>
> May 8 17:31:39 rocky scsi: [ID 107833 kern.notice] Sense Key: 
> Soft_Error
>
> May 8 17:31:39 rocky scsi: [ID 107833 kern.notice] ASC: 0x0 (no 
> additional sense info), ASCQ: 0x0, FRU: 0x0
>
> How can I avoid these warnings (which reappear every 30 minutes from 
> smartd)?
>
>    

The solaris specific code was not changed between 5.39 and 5.40. The commands 0x85 and 0xa1 are the 16 and 12
byte versions of SAT ATA PASS-THROUGH 16 and 12 which are used to for all ATA commands if '-d sat' is specified.

"smartctl -a" is equivalent to "smartctl -H -i -c -A -l error -l selftest -l selective". Please try which of
those options produce a kernel warning.

Thanks,
Christian

------------------------------------------------------------------------------
WhatsUp Gold - Download Free Network Management Software
The most intuitive, comprehensive, and cost-effective network 
management toolset available today.  Delivers lowest initial 
acquisition cost and overall TCO of any competing solution.
http://p.sf.net/sfu/whatsupgold-sd
Permalink | Reply | 6 comments |
headers
Christoph Anton Mitterer | 8 May 2011 03:49
Gravatar

adding support for (another) Hitachi/SimpleTech USB connected HDD

Hi.

I have an external 1 TB Hitachi HDD connected via USB.

I has however a different USB ID as the one already in the DB.
Perhaps the following is useful for you. Ask if you need more information.

Aand keep me CCed, as I'm writing off list.

Cheers,
Chris.

# lsusb 
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 002: ID 1a40:0201 TERMINUS TECHNOLOGY INC. 
Bus 002 Device 002: ID 2040:9950 Hauppauge WinTV Nova-T-500
Bus 003 Device 002: ID 045e:00db Microsoft Corp. Natural Ergonomic
Keyboard 4000 V1.0
Bus 001 Device 004: ID 046d:08b2 Logitech, Inc. QuickCam Pro 4000
Bus 001 Device 005: ID 076b:5121 OmniKey AG CardMan 5121
Bus 001 Device 007: ID 4971:ce23 SimpleTech 

# smartctl -a -d usbjmicron  /dev/sde
smartctl 5.41 2011-03-16 r3296 [x86_64-unknown-linux-gnu-2.6.37-fermat]
(local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Model Family:     Hitachi Deskstar 7K1000.C
Device Model:     Hitachi HDS721010CLA332
Serial Number:    JP2921HQ05LPUA
Firmware Version: JP4OA25C
User Capacity:    1,000,204,886,016 bytes
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   8
ATA Standard is:  ATA-8-ACS revision 4
Local Time is:    Sun May  8 03:44:40 2011 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x84)	Offline data collection activity
					was suspended by an interrupting command from host.
					Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)	The previous self-test routine
completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(10047) seconds.
Offline data collection
capabilities: 			 (0x5b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 ( 167) minutes.
SCT capabilities: 	       (0x003d)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED 
WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000b   100   100   016    Pre-fail  Always  
   -       1
  2 Throughput_Performance  0x0005   136   136   054    Pre-fail  Offline 
   -       92
  3 Spin_Up_Time            0x0007   125   125   024    Pre-fail  Always  
   -       287 (Average 320)
  4 Start_Stop_Count        0x0012   100   100   000    Old_age   Always  
   -       20
  5 Reallocated_Sector_Ct   0x0033   100   100   005    Pre-fail  Always  
   -       0
  7 Seek_Error_Rate         0x000b   100   100   067    Pre-fail  Always  
   -       0
  8 Seek_Time_Performance   0x0005   100   100   020    Pre-fail  Offline 
   -       0
  9 Power_On_Hours          0x0012   100   100   000    Old_age   Always  
   -       27
 10 Spin_Retry_Count        0x0013   100   100   060    Pre-fail  Always  
   -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always  
   -       17
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always  
   -       20
193 Load_Cycle_Count        0x0012   100   100   000    Old_age   Always  
   -       20
194 Temperature_Celsius     0x0002   125   125   000    Old_age   Always  
   -       48 (Min/Max 21/52)
196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always  
   -       0
197 Current_Pending_Sector  0x0022   100   100   000    Old_age   Always  
   -       0
198 Offline_Uncorrectable   0x0008   100   100   000    Old_age   Offline 
   -       0
199 UDMA_CRC_Error_Count    0x000a   200   200   000    Old_age   Always  
   -       0

SMART Error Log Version: 0
No Errors Logged

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute
delay.

------------------------------------------------------------------------------
Achieve unprecedented app performance and reliability
What every C/C++ and Fortran developer should know.
Learn how Intel has extended the reach of its next-generation tools
to help boost performance applications - inlcuding clusters.
http://p.sf.net/sfu/intel-dev2devmay
Permalink | Reply | 0 comments |
headers
Alexander Shaduri | 11 May 2011 19:39
Picon

Test stuck at 90% on 3ware / Windows - couldn't reproduce


Hello,

Just writing to say that I couldn't reproduce the bug I encountered earlier
and described at:
https://sourceforge.net/apps/trac/smartmontools/ticket/165#comment:5
The bug was the short being test stuck at 90% under Windows with
a 3ware controller.

I tried reproducing it a couple of times today (with the same configuration,
but slightly newer smartmontools - 5.41-0-20110419-r3317), and there was
no problem.

Instead of opening a new bug or polluting the old one with unrelated
comments, I thought I'd just send the message here.

Thanks,
Alexander

------------------------------------------------------------------------------
Achieve unprecedented app performance and reliability
What every C/C++ and Fortran developer should know.
Learn how Intel has extended the reach of its next-generation tools
to help boost performance applications - inlcuding clusters.
http://p.sf.net/sfu/intel-dev2devmay
Permalink | Reply | 1 comment |
headers
Christian Franke | 16 May 2011 20:23
Picon
Favicon

Re: Test stuck at 90% on 3ware / Windows - couldn't reproduce

Alexander Shaduri wrote:
> Just writing to say that I couldn't reproduce the bug I encountered earlier
> and described at:
> https://sourceforge.net/apps/trac/smartmontools/ticket/165#comment:5
> The bug was the short being test stuck at 90% under Windows with
> a 3ware controller.
>
> I tried reproducing it a couple of times today (with the same configuration,
> but slightly newer smartmontools - 5.41-0-20110419-r3317), and there was
> no problem.
>
>    

Probably this occurs occasionally due to a disk firmware bug.

Thanks for the feedback,
Christian

------------------------------------------------------------------------------
Achieve unprecedented app performance and reliability
What every C/C++ and Fortran developer should know.
Learn how Intel has extended the reach of its next-generation tools
to help boost performance applications - inlcuding clusters.
http://p.sf.net/sfu/intel-dev2devmay
Permalink | Reply | 0 comments |
headers
Christian Franke | 17 May 2011 23:48
Picon
Favicon

Re: Kernel errors on Solaris 11 x64 after moving from 5.39 to 5.40

Peter Radig wrote:
> It's the "-H" that causes the grief.
>
>    

This is the only SMART command which requires ATA output registers. When 
SAT ATA PASS-THROUGH is used this requires proper transfer of sense data.

Both the solaris code and the OS independent SAT code are not changed 
between 5.39 and 5.40. But the number and order of commands issued have 
changed.

For further diagnostics please provide outputs of "smartctl -r ioctl,2 
-H /dev/ice" from 5.39 and 5.40.

Thanks,
Christian

------------------------------------------------------------------------------
What Every C/C++ and Fortran developer Should Know!
Read this article and learn how Intel has extended the reach of its 
next-generation tools to help Windows* and Linux* C/C++ and Fortran 
developers boost performance applications - including clusters. 
http://p.sf.net/sfu/intel-dev2devmay
Permalink | Reply | 5 comments |
headers
Peter Radig | 18 May 2011 08:11
Picon

Re: Kernel errors on Solaris 11 x64 after moving from 5.39 to 5.40

peter <at> rocky:~/src/smartmontools-5.39$ pfexec ./smartctl -d sat,12 -r ioctl,2 -H /dev/rdsk/c12t0d0p0
smartctl 5.39 2009-12-09 r2995 [i386-pc-solaris2.11] (local build)
Copyright (C) 2002-9 by Bruce Allen, http://smartmontools.sourceforge.net

REPORT-IOCTL: Device=/dev/rdsk/c12t0d0p0 Command=IDENTIFY DEVICE
 Input:   FR=...., SC=0x01, LL=...., LM=...., LH=...., DEV=...., CMD=0xec IN
 [ata pass-through(12): a1 08 0e 00 01 00 00 00 00 ec 00 00 ]
  Incoming data, len=512 [only first 256 bytes shown]:
 00     7a 42 ff 3f 37 c8 10 00  00 00 00 00 3f 00 00 00                        
 10     00 00 00 00 20 20 20 20  57 20 2d 44 58 57 30 33                        
 20     43 41 4e 39 36 38 37 37  00 00 00 80 32 00 32 30                        
 30     30 2e 41 31 32 30 44 57  20 43 44 57 32 33 30 30                        
 40     45 42 54 4b 32 2d 41 32  35 32 31 54 20 20 20 20                        
 50     20 20 20 20 20 20 20 20  20 20 20 20 20 20 10 80                        
 60     00 00 00 2f 01 40 00 00  00 00 07 00 ff 3f 10 00                        
 70     3f 00 10 fc fb 00 00 01  ff ff ff 0f 00 00 07 00                        
 80     03 00 78 00 78 00 78 00  78 00 00 00 00 00 00 00                        
 90     00 00 00 00 00 00 1f 00  06 1f 00 00 4c 00 40 00                        
 a0     fe 01 00 00 6b 74 09 7f  63 61 69 74 09 bc 63 61                        
 b0     7f 40 1e 00 1e 00 60 00  fe ff 00 00 fe 80 00 00                        
 c0     00 00 00 00 00 00 00 00  b0 ea 42 25 00 00 00 00                        
 d0     00 00 00 00 00 00 00 00  01 50 e2 4e a8 ae ba c2                        
 e0     00 00 00 00 00 00 00 00  00 00 00 00 00 00 18 40                        
 f0     18 40 00 00 00 00 00 00  00 00 00 00 00 00 00 00                        
REPORT-IOCTL: Device=/dev/rdsk/c12t0d0p0 Command=IDENTIFY DEVICE returned 0

===== [IDENTIFY DEVICE] DATA START (BASE-16) =====
000-015: 7a 42 ff 3f 37 c8 10 00 00 00 00 00 3f 00 00 00
016-031: 00 00 00 00 20 20 20 20 57 20 2d 44 58 57 30 33
032-047: 43 41 4e 39 36 38 37 37 00 00 00 80 32 00 32 30
048-063: 30 2e 41 31 32 30 44 57 20 43 44 57 32 33 30 30
064-079: 45 42 54 4b 32 2d 41 32 35 32 31 54 20 20 20 20
080-095: 20 20 20 20 20 20 20 20 20 20 20 20 20 20 10 80
096-111: 00 00 00 2f 01 40 00 00 00 00 07 00 ff 3f 10 00
112-127: 3f 00 10 fc fb 00 00 01 ff ff ff 0f 00 00 07 00
128-143: 03 00 78 00 78 00 78 00 78 00 00 00 00 00 00 00
144-159: 00 00 00 00 00 00 1f 00 06 1f 00 00 4c 00 40 00
160-175: fe 01 00 00 6b 74 09 7f 63 61 69 74 09 bc 63 61
176-191: 7f 40 1e 00 1e 00 60 00 fe ff 00 00 fe 80 00 00
192-207: 00 00 00 00 00 00 00 00 b0 ea 42 25 00 00 00 00
208-223: 00 00 00 00 00 00 00 00 01 50 e2 4e a8 ae ba c2
224-239: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 18 40
240-255: 18 40 00 00 00 00 00 00 00 00 00 00 00 00 00 00
256-271: 21 00 00 00 00 00 00 00 00 00 c7 16 00 00 00 00
272-287: 00 00 00 00 00 00 00 00 00 00 00 00 04 00 00 00
288-303: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
304-319: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
320-335: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
336-351: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
352-367: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
368-383: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
384-399: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
400-415: 00 00 00 00 00 00 00 00 00 00 00 00 37 70 00 00
416-431: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
432-447: 00 00 20 1c 00 00 00 00 00 00 00 00 1e 10 00 00
448-463: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
464-479: 00 00 00 00 01 00 00 10 00 00 00 00 00 00 00 00
480-495: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
496-511: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a5 fa
===== [IDENTIFY DEVICE] DATA END (512 Bytes) =====

REPORT-IOCTL: Device=/dev/rdsk/c12t0d0p0 Command=SMART STATUS
 Input:   FR=0xda, SC=...., LL=...., LM=0x4f, LH=0xc2, DEV=...., CMD=0xb0
 [ata pass-through(12): a1 06 0c da 00 00 4f c2 00 b0 00 00 ]
REPORT-IOCTL: Device=/dev/rdsk/c12t0d0p0 Command=SMART STATUS returned 0

REPORT-IOCTL: Device=/dev/rdsk/c12t0d0p0 Command=SMART STATUS CHECK
 Input:   FR=0xda, SC=...., LL=...., LM=0x4f, LH=0xc2, DEV=...., CMD=0xb0
 [ata pass-through(12): a1 06 2c da 00 00 4f c2 00 b0 00 00 ]
  status=0x2: sense_key=0x0 asc=0x0 ascq=0x0
  >>> Sense buffer, len=24:
 00     72 01 00 00 00 00 00 0e  09 0c 00 00 00 00 00 00                        
 10     00 4f 00 c2 00 00 00 00                                                 
Values from ATA Return Descriptor are:
 00     09 0c 00 00 00 00 00 00  00 4f 00 c2 00 00                              
 Output: ERR=0x00, SC=0x00, LL=0x00, LM=0x4f, LH=0xc2, DEV=0x00, STS=0x00
REPORT-IOCTL: Device=/dev/rdsk/c12t0d0p0 Command=SMART STATUS CHECK returned 0

REPORT-IOCTL: Device=/dev/rdsk/c12t0d0p0 Command=SMART READ ATTRIBUTE VALUES
 Input:   FR=0xd0, SC=0x01, LL=...., LM=0x4f, LH=0xc2, DEV=...., CMD=0xb0 IN
 [ata pass-through(12): a1 08 0e d0 01 00 4f c2 00 b0 00 00 ]
  Incoming data, len=512 [only first 256 bytes shown]:
 00     10 00 01 2f 00 c8 c8 00  00 00 00 00 00 00 03 27                        
 10     00 90 8f ef 06 00 00 00  00 00 04 32 00 64 64 0f                        
 20     00 00 00 00 00 00 05 33  00 c8 c8 00 00 00 00 00                        
 30     00 00 07 2e 00 c8 c8 00  00 00 00 00 00 00 09 32                        
 40     00 5d 5d 9f 14 00 00 00  00 00 0a 32 00 64 fd 00                        
 50     00 00 00 00 00 00 0b 32  00 64 fd 00 00 00 00 00                        
 60     00 00 0c 32 00 64 64 0e  00 00 00 00 00 00 bf 32                        
 70     00 5e 5e 06 00 00 00 00  00 00 c0 32 00 c8 c8 0d                        
 80     00 00 00 00 00 00 c1 32  00 9e 9e 03 f1 01 00 00                        
 90     00 00 c2 22 00 6b 5b 24  00 00 00 00 00 00 c4 32                        
 a0     00 c8 c8 00 00 00 00 00  00 00 c5 32 00 c8 c8 00                        
 b0     00 00 00 00 00 00 c6 30  00 c8 c8 00 00 00 00 00                        
 c0     00 00 c7 32 00 c8 c8 00  00 00 00 00 00 00 c8 08                        
 d0     00 c8 c8 00 00 00 00 00  00 00 00 00 00 00 00 00                        
 e0     00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00                        
 f0     00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00                        
REPORT-IOCTL: Device=/dev/rdsk/c12t0d0p0 Command=SMART READ ATTRIBUTE VALUES returned 0

===== [SMART READ ATTRIBUTE VALUES] DATA START (BASE-16) =====
000-015: 10 00 01 2f 00 c8 c8 00 00 00 00 00 00 00 03 27
016-031: 00 90 8f ef 06 00 00 00 00 00 04 32 00 64 64 0f
032-047: 00 00 00 00 00 00 05 33 00 c8 c8 00 00 00 00 00
048-063: 00 00 07 2e 00 c8 c8 00 00 00 00 00 00 00 09 32
064-079: 00 5d 5d 9f 14 00 00 00 00 00 0a 32 00 64 fd 00
080-095: 00 00 00 00 00 00 0b 32 00 64 fd 00 00 00 00 00
096-111: 00 00 0c 32 00 64 64 0e 00 00 00 00 00 00 bf 32
112-127: 00 5e 5e 06 00 00 00 00 00 00 c0 32 00 c8 c8 0d
128-143: 00 00 00 00 00 00 c1 32 00 9e 9e 03 f1 01 00 00
144-159: 00 00 c2 22 00 6b 5b 24 00 00 00 00 00 00 c4 32
160-175: 00 c8 c8 00 00 00 00 00 00 00 c5 32 00 c8 c8 00
176-191: 00 00 00 00 00 00 c6 30 00 c8 c8 00 00 00 00 00
192-207: 00 00 c7 32 00 c8 c8 00 00 00 00 00 00 00 c8 08
208-223: 00 c8 c8 00 00 00 00 00 00 00 00 00 00 00 00 00
224-239: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
240-255: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
256-271: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
272-287: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
288-303: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
304-319: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
320-335: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
336-351: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
352-367: 00 00 00 00 00 00 00 00 00 00 84 00 70 17 01 7b
368-383: 03 00 01 00 02 49 05 00 00 00 00 00 00 00 00 00
384-399: 00 00 01 02 00 00 00 00 00 00 00 00 00 00 00 00
400-415: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
416-431: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
432-447: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
448-463: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
464-479: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
480-495: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
496-511: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d3
===== [SMART READ ATTRIBUTE VALUES] DATA END (512 Bytes) =====

REPORT-IOCTL: Device=/dev/rdsk/c12t0d0p0 Command=SMART READ ATTRIBUTE THRESHOLDS
 Input:   FR=0xd1, SC=0x01, LL=0x01, LM=0x4f, LH=0xc2, DEV=...., CMD=0xb0 IN
 [ata pass-through(12): a1 08 0e d1 01 01 4f c2 00 b0 00 00 ]
  Incoming data, len=512 [only first 256 bytes shown]:
 00     10 00 01 33 c8 c8 00 00  00 00 00 00 00 00 03 15                        
 10     00 00 00 00 00 00 00 00  00 00 04 00 00 00 00 00                        
 20     00 00 00 00 00 00 05 8c  00 00 00 00 00 00 00 00                        
 30     00 00 07 00 c8 c8 00 00  00 00 00 00 00 00 09 00                        
 40     00 00 00 00 00 00 00 00  00 00 0a 00 00 00 00 00                        
 50     00 00 00 00 00 00 0b 00  00 00 00 00 00 00 00 00                        
 60     00 00 0c 00 00 00 00 00  00 00 00 00 00 00 bf 00                        
 70     00 00 00 00 00 00 00 00  00 00 c0 00 00 00 00 00                        
 80     00 00 00 00 00 00 c1 00  00 00 00 00 00 00 00 00                        
 90     00 00 c2 00 00 00 00 00  00 00 00 00 00 00 c4 00                        
 a0     00 00 00 00 00 00 00 00  00 00 c5 00 00 00 00 00                        
 b0     00 00 00 00 00 00 c6 00  00 00 00 00 00 00 00 00                        
 c0     00 00 c7 00 00 00 00 00  00 00 00 00 00 00 c8 00                        
 d0     c8 c8 00 00 00 00 00 00  00 00 00 00 00 00 00 00                        
 e0     00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00                        
 f0     00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00                        
REPORT-IOCTL: Device=/dev/rdsk/c12t0d0p0 Command=SMART READ ATTRIBUTE THRESHOLDS returned 0

===== [SMART READ ATTRIBUTE THRESHOLDS] DATA START (BASE-16) =====
000-015: 10 00 01 33 c8 c8 00 00 00 00 00 00 00 00 03 15
016-031: 00 00 00 00 00 00 00 00 00 00 04 00 00 00 00 00
032-047: 00 00 00 00 00 00 05 8c 00 00 00 00 00 00 00 00
048-063: 00 00 07 00 c8 c8 00 00 00 00 00 00 00 00 09 00
064-079: 00 00 00 00 00 00 00 00 00 00 0a 00 00 00 00 00
080-095: 00 00 00 00 00 00 0b 00 00 00 00 00 00 00 00 00
096-111: 00 00 0c 00 00 00 00 00 00 00 00 00 00 00 bf 00
112-127: 00 00 00 00 00 00 00 00 00 00 c0 00 00 00 00 00
128-143: 00 00 00 00 00 00 c1 00 00 00 00 00 00 00 00 00
144-159: 00 00 c2 00 00 00 00 00 00 00 00 00 00 00 c4 00
160-175: 00 00 00 00 00 00 00 00 00 00 c5 00 00 00 00 00
176-191: 00 00 00 00 00 00 c6 00 00 00 00 00 00 00 00 00
192-207: 00 00 c7 00 00 00 00 00 00 00 00 00 00 00 c8 00
208-223: c8 c8 00 00 00 00 00 00 00 00 00 00 00 00 00 00
224-239: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
240-255: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
256-271: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
272-287: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
288-303: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
304-319: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
320-335: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
336-351: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
352-367: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
368-383: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
384-399: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
400-415: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
416-431: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
432-447: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
448-463: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
464-479: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
480-495: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
496-511: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 4e
===== [SMART READ ATTRIBUTE THRESHOLDS] DATA END (512 Bytes) =====

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

peter <at> rocky:~/src/smartmontools-5.39$

peter <at> rocky:~/src/smartmontools-5.40$ pfexec ./smartctl -d sat,12 -r ioctl,2 -H /dev/rdsk/c12t0d0p0
smartctl 5.40 2010-10-16 r3189 [i386-pc-solaris2.11] (local build)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net

REPORT-IOCTL: Device=/dev/rdsk/c12t0d0p0 Command=IDENTIFY DEVICE
 Input:   FR=...., SC=0x01, LL=...., LM=...., LH=...., DEV=...., CMD=0xec IN
 [ata pass-through(12): a1 08 0e 00 01 00 00 00 00 ec 00 00 ]
  Incoming data, len=512 [only first 256 bytes shown]:
 00     7a 42 ff 3f 37 c8 10 00  00 00 00 00 3f 00 00 00                        
 10     00 00 00 00 20 20 20 20  57 20 2d 44 58 57 30 33                        
 20     43 41 4e 39 36 38 37 37  00 00 00 80 32 00 32 30                        
 30     30 2e 41 31 32 30 44 57  20 43 44 57 32 33 30 30                        
 40     45 42 54 4b 32 2d 41 32  35 32 31 54 20 20 20 20                        
 50     20 20 20 20 20 20 20 20  20 20 20 20 20 20 10 80                        
 60     00 00 00 2f 01 40 00 00  00 00 07 00 ff 3f 10 00                        
 70     3f 00 10 fc fb 00 00 01  ff ff ff 0f 00 00 07 00                        
 80     03 00 78 00 78 00 78 00  78 00 00 00 00 00 00 00                        
 90     00 00 00 00 00 00 1f 00  06 1f 00 00 4c 00 40 00                        
 a0     fe 01 00 00 6b 74 09 7f  63 61 69 74 09 bc 63 61                        
 b0     7f 40 1e 00 1e 00 60 00  fe ff 00 00 fe 80 00 00                        
 c0     00 00 00 00 00 00 00 00  b0 ea 42 25 00 00 00 00                        
 d0     00 00 00 00 00 00 00 00  01 50 e2 4e a8 ae ba c2                        
 e0     00 00 00 00 00 00 00 00  00 00 00 00 00 00 18 40                        
 f0     18 40 00 00 00 00 00 00  00 00 00 00 00 00 00 00                        
REPORT-IOCTL: Device=/dev/rdsk/c12t0d0p0 Command=IDENTIFY DEVICE returned 0

===== [IDENTIFY DEVICE] DATA START (BASE-16) =====
000-015: 7a 42 ff 3f 37 c8 10 00 00 00 00 00 3f 00 00 00 |zB.?7.......?...|
016-031: 00 00 00 00 20 20 20 20 57 20 2d 44 58 57 30 33 |....    W -DXW03|
032-047: 43 41 4e 39 36 38 37 37 00 00 00 80 32 00 32 30 |CAN96877....2.20|
048-063: 30 2e 41 31 32 30 44 57 20 43 44 57 32 33 30 30 |0.A120DW CDW2300|
064-079: 45 42 54 4b 32 2d 41 32 35 32 31 54 20 20 20 20 |EBTK2-A2521T    |
080-095: 20 20 20 20 20 20 20 20 20 20 20 20 20 20 10 80 |              ..|
096-111: 00 00 00 2f 01 40 00 00 00 00 07 00 ff 3f 10 00 |.../. <at> .......?..|
112-127: 3f 00 10 fc fb 00 00 01 ff ff ff 0f 00 00 07 00 |?...............|
128-143: 03 00 78 00 78 00 78 00 78 00 00 00 00 00 00 00 |..x.x.x.x.......|
144-159: 00 00 00 00 00 00 1f 00 06 1f 00 00 4c 00 40 00 |............L. <at> .|
160-175: fe 01 00 00 6b 74 09 7f 63 61 69 74 09 bc 63 61 |....kt..cait..ca|
176-191: 7f 40 1e 00 1e 00 60 00 fe ff 00 00 fe 80 00 00 |. <at> ....`.........|
192-207: 00 00 00 00 00 00 00 00 b0 ea 42 25 00 00 00 00 |..........B%....|
208-223: 00 00 00 00 00 00 00 00 01 50 e2 4e a8 ae ba c2 |.........P.N....|
224-239: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 18 40 |............... <at> |
240-255: 18 40 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |. <at> ..............|
256-271: 21 00 00 00 00 00 00 00 00 00 c7 16 00 00 00 00 |!...............|
272-287: 00 00 00 00 00 00 00 00 00 00 00 00 04 00 00 00 |................|
288-303: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
304-319: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
320-335: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
336-351: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
352-367: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
368-383: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
384-399: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
400-415: 00 00 00 00 00 00 00 00 00 00 00 00 37 70 00 00 |............7p..|
416-431: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
432-447: 00 00 20 1c 00 00 00 00 00 00 00 00 1e 10 00 00 |.. .............|
448-463: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
464-479: 00 00 00 00 01 00 00 10 00 00 00 00 00 00 00 00 |................|
480-495: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
496-511: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a5 fa |................|
===== [IDENTIFY DEVICE] DATA END (512 Bytes) =====

REPORT-IOCTL: Device=/dev/rdsk/c12t0d0p0 Command=SMART READ ATTRIBUTE VALUES
 Input:   FR=0xd0, SC=0x01, LL=...., LM=0x4f, LH=0xc2, DEV=...., CMD=0xb0 IN
 [ata pass-through(12): a1 08 0e d0 01 00 4f c2 00 b0 00 00 ]
  Incoming data, len=512 [only first 256 bytes shown]:
 00     10 00 01 2f 00 c8 c8 00  00 00 00 00 00 00 03 27                        
 10     00 90 8f ef 06 00 00 00  00 00 04 32 00 64 64 0f                        
 20     00 00 00 00 00 00 05 33  00 c8 c8 00 00 00 00 00                        
 30     00 00 07 2e 00 c8 c8 00  00 00 00 00 00 00 09 32                        
 40     00 5d 5d 9f 14 00 00 00  00 00 0a 32 00 64 fd 00                        
 50     00 00 00 00 00 00 0b 32  00 64 fd 00 00 00 00 00                        
 60     00 00 0c 32 00 64 64 0e  00 00 00 00 00 00 bf 32                        
 70     00 5e 5e 06 00 00 00 00  00 00 c0 32 00 c8 c8 0d                        
 80     00 00 00 00 00 00 c1 32  00 9e 9e 07 f1 01 00 00                        
 90     00 00 c2 22 00 6b 5b 24  00 00 00 00 00 00 c4 32                        
 a0     00 c8 c8 00 00 00 00 00  00 00 c5 32 00 c8 c8 00                        
 b0     00 00 00 00 00 00 c6 30  00 c8 c8 00 00 00 00 00                        
 c0     00 00 c7 32 00 c8 c8 00  00 00 00 00 00 00 c8 08                        
 d0     00 c8 c8 00 00 00 00 00  00 00 00 00 00 00 00 00                        
 e0     00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00                        
 f0     00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00                        
REPORT-IOCTL: Device=/dev/rdsk/c12t0d0p0 Command=SMART READ ATTRIBUTE VALUES returned 0

===== [SMART READ ATTRIBUTE VALUES] DATA START (BASE-16) =====
000-015: 10 00 01 2f 00 c8 c8 00 00 00 00 00 00 00 03 27 |.../...........'|
016-031: 00 90 8f ef 06 00 00 00 00 00 04 32 00 64 64 0f |...........2.dd.|
032-047: 00 00 00 00 00 00 05 33 00 c8 c8 00 00 00 00 00 |.......3........|
048-063: 00 00 07 2e 00 c8 c8 00 00 00 00 00 00 00 09 32 |...............2|
064-079: 00 5d 5d 9f 14 00 00 00 00 00 0a 32 00 64 fd 00 |.]]........2.d..|
080-095: 00 00 00 00 00 00 0b 32 00 64 fd 00 00 00 00 00 |.......2.d......|
096-111: 00 00 0c 32 00 64 64 0e 00 00 00 00 00 00 bf 32 |...2.dd........2|
112-127: 00 5e 5e 06 00 00 00 00 00 00 c0 32 00 c8 c8 0d |.^^........2....|
128-143: 00 00 00 00 00 00 c1 32 00 9e 9e 07 f1 01 00 00 |.......2........|
144-159: 00 00 c2 22 00 6b 5b 24 00 00 00 00 00 00 c4 32 |...".k[$.......2|
160-175: 00 c8 c8 00 00 00 00 00 00 00 c5 32 00 c8 c8 00 |...........2....|
176-191: 00 00 00 00 00 00 c6 30 00 c8 c8 00 00 00 00 00 |.......0........|
192-207: 00 00 c7 32 00 c8 c8 00 00 00 00 00 00 00 c8 08 |...2............|
208-223: 00 c8 c8 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
224-239: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
240-255: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
256-271: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
272-287: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
288-303: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
304-319: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
320-335: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
336-351: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
352-367: 00 00 00 00 00 00 00 00 00 00 84 00 70 17 01 7b |............p..{|
368-383: 03 00 01 00 02 49 05 00 00 00 00 00 00 00 00 00 |.....I..........|
384-399: 00 00 01 02 00 00 00 00 00 00 00 00 00 00 00 00 |................|
400-415: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
416-431: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
432-447: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
448-463: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
464-479: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
480-495: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
496-511: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 cf |................|
===== [SMART READ ATTRIBUTE VALUES] DATA END (512 Bytes) =====

REPORT-IOCTL: Device=/dev/rdsk/c12t0d0p0 Command=SMART READ ATTRIBUTE THRESHOLDS
 Input:   FR=0xd1, SC=0x01, LL=0x01, LM=0x4f, LH=0xc2, DEV=...., CMD=0xb0 IN
 [ata pass-through(12): a1 08 0e d1 01 01 4f c2 00 b0 00 00 ]
  Incoming data, len=512 [only first 256 bytes shown]:
 00     10 00 01 33 c8 c8 00 00  00 00 00 00 00 00 03 15                        
 10     00 00 00 00 00 00 00 00  00 00 04 00 00 00 00 00                        
 20     00 00 00 00 00 00 05 8c  00 00 00 00 00 00 00 00                        
 30     00 00 07 00 c8 c8 00 00  00 00 00 00 00 00 09 00                        
 40     00 00 00 00 00 00 00 00  00 00 0a 00 00 00 00 00                        
 50     00 00 00 00 00 00 0b 00  00 00 00 00 00 00 00 00                        
 60     00 00 0c 00 00 00 00 00  00 00 00 00 00 00 bf 00                        
 70     00 00 00 00 00 00 00 00  00 00 c0 00 00 00 00 00                        
 80     00 00 00 00 00 00 c1 00  00 00 00 00 00 00 00 00                        
 90     00 00 c2 00 00 00 00 00  00 00 00 00 00 00 c4 00                        
 a0     00 00 00 00 00 00 00 00  00 00 c5 00 00 00 00 00                        
 b0     00 00 00 00 00 00 c6 00  00 00 00 00 00 00 00 00                        
 c0     00 00 c7 00 00 00 00 00  00 00 00 00 00 00 c8 00                        
 d0     c8 c8 00 00 00 00 00 00  00 00 00 00 00 00 00 00                        
 e0     00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00                        
 f0     00 00 00 00 00 00 00 00  00 00 00 00 00 00 00 00                        
REPORT-IOCTL: Device=/dev/rdsk/c12t0d0p0 Command=SMART READ ATTRIBUTE THRESHOLDS returned 0

===== [SMART READ ATTRIBUTE THRESHOLDS] DATA START (BASE-16) =====
000-015: 10 00 01 33 c8 c8 00 00 00 00 00 00 00 00 03 15 |...3............|
016-031: 00 00 00 00 00 00 00 00 00 00 04 00 00 00 00 00 |................|
032-047: 00 00 00 00 00 00 05 8c 00 00 00 00 00 00 00 00 |................|
048-063: 00 00 07 00 c8 c8 00 00 00 00 00 00 00 00 09 00 |................|
064-079: 00 00 00 00 00 00 00 00 00 00 0a 00 00 00 00 00 |................|
080-095: 00 00 00 00 00 00 0b 00 00 00 00 00 00 00 00 00 |................|
096-111: 00 00 0c 00 00 00 00 00 00 00 00 00 00 00 bf 00 |................|
112-127: 00 00 00 00 00 00 00 00 00 00 c0 00 00 00 00 00 |................|
128-143: 00 00 00 00 00 00 c1 00 00 00 00 00 00 00 00 00 |................|
144-159: 00 00 c2 00 00 00 00 00 00 00 00 00 00 00 c4 00 |................|
160-175: 00 00 00 00 00 00 00 00 00 00 c5 00 00 00 00 00 |................|
176-191: 00 00 00 00 00 00 c6 00 00 00 00 00 00 00 00 00 |................|
192-207: 00 00 c7 00 00 00 00 00 00 00 00 00 00 00 c8 00 |................|
208-223: c8 c8 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
224-239: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
240-255: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
256-271: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
272-287: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
288-303: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
304-319: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
320-335: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
336-351: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
352-367: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
368-383: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
384-399: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
400-415: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
416-431: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
432-447: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
448-463: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
464-479: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
480-495: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
496-511: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 4e |...............N|
===== [SMART READ ATTRIBUTE THRESHOLDS] DATA END (512 Bytes) =====

=== START OF READ SMART DATA SECTION ===

REPORT-IOCTL: Device=/dev/rdsk/c12t0d0p0 Command=SMART STATUS CHECK
 Input:   FR=0xda, SC=...., LL=...., LM=0x4f, LH=0xc2, DEV=...., CMD=0xb0
 [ata pass-through(12): a1 06 2c da 00 00 4f c2 00 b0 00 00 ]
  status=0x2: sense_key=0x0 asc=0x0 ascq=0x0
  >>> Sense buffer, len=24:
 00     72 01 00 00 00 00 00 0e  09 0c 00 00 00 00 00 00                        
 10     00 4f 00 c2 00 00 00 00                                                 
Values from ATA Return Descriptor are:
 00     09 0c 00 00 00 00 00 00  00 4f 00 c2 00 00                              
 Output: ERR=0x00, SC=0x00, LL=0x00, LM=0x4f, LH=0xc2, DEV=0x00, STS=0x00
REPORT-IOCTL: Device=/dev/rdsk/c12t0d0p0 Command=SMART STATUS CHECK returned 0
SMART overall-health self-assessment test result: PASSED

peter <at> rocky:~/src/smartmontools-5.40$

May 18 08:07:42 rocky   Error for Command: <undecoded cmd 0xa1>    Error Level: Recovered
May 18 08:07:42 rocky scsi: [ID 107833 kern.notice]     Requested Block: 0                         Error Block: 0
May 18 08:07:42 rocky scsi: [ID 107833 kern.notice]     Vendor: ATA                                Serial Number:             
May 18 08:07:42 rocky scsi: [ID 107833 kern.notice]     Sense Key: Soft_Error
May 18 08:07:42 rocky scsi: [ID 107833 kern.notice]     ASC: 0x0 (no additional sense info), ASCQ: 0x0, FRU: 0x0

Thanks,
Peter

-----Original Message-----
From: Christian Franke [mailto:Christian.Franke <at> t-online.de] 
Sent: Dienstag, 17. Mai 2011 23:49
To: Peter Radig
Cc: smartmontools-support <at> lists.sourceforge.net
Subject: Re: [smartmontools-support] Kernel errors on Solaris 11 x64 after moving from 5.39 to 5.40

Peter Radig wrote:
> It's the "-H" that causes the grief.
>
>    

This is the only SMART command which requires ATA output registers. When SAT ATA PASS-THROUGH is used this
requires proper transfer of sense data.

Both the solaris code and the OS independent SAT code are not changed between 5.39 and 5.40. But the number
and order of commands issued have changed.

For further diagnostics please provide outputs of "smartctl -r ioctl,2 -H /dev/ice" from 5.39 and 5.40.

Thanks,
Christian

------------------------------------------------------------------------------
What Every C/C++ and Fortran developer Should Know!
Read this article and learn how Intel has extended the reach of its 
next-generation tools to help Windows* and Linux* C/C++ and Fortran 
developers boost performance applications - including clusters. 
http://p.sf.net/sfu/intel-dev2devmay
Permalink | Reply | 4 comments |
headers
Fab35 | 18 May 2011 17:40
Picon
Picon

Re: scteHD204UI on ICH10R in RAID5


Christian Franke wrote:
> 
>> I try to build a RAID 5 array on an ASUS P5QD Turbo with ICH10R. The
>> HD204UI
>> work quite well when not in RAID but in AHCI mode and I can set scterc to
>> 70
>> as needed. Ah, it is running on an Win 2008 R2 host.
>>
>> Two problems: When creating a RAID 5 array I can still access the drives
>> individually with smartctl via /dev/csmiX,X but the set parameter turns
>> out
>> to be 57345 now. I can still set the sctecr again to 70 - no error
>> message,
>> but if I check it again it's still 37345.
>>    
> 
> The SCT ERC Get command requires ATA output registers from SMART WRITE 
> LOG command which might not be supported by all drivers. The ERC Set 
> command does not need output registers, so Set might work while Get
> doesn't.
> 
> Intel RAID version? "smartctl -l scterc" worked for me with Intel RAID 
> 5.5 and 8.8.
> 
> Does "smartctl -H" work properly? This command also requires ATA output 
> registers.
> 

Mhm, I'm not sure about the driver version. Device manager says 10.1.
0.1008 for the controller. But within the storage manager I can't find any
version number. I remember that the ROM version was quite old actually and
the storage manager tells me, that the ROM is not compatible with disks
equal or larger than 1.5 TB. It still works from within the storage manager
though.

smartctl -H works, as does smartctl -a. 

Christian Franke wrote:
> 
>> What to do? Ignore and believe it's still 70? I fear of the devices
>> dropping
>> out of the array. Maybe it's not set correctly, maybe it's just a problem
>> of
>> reading the value when in RAID and it actually IS 70. When I delete the
>> RAID
>> volume and check the disks individually it IS 70.
> 
> Which driver was used after deleting the RAID: Still Intel RAID driver 
> or some other (AHCI) driver?
> 
> If you could repeat the test (set in RAID mode, get in non-RAID mode) 
> with some other values (e.g. 75,80) the you could assume that ERC Set
> works.
> (BTW: smartd could now also set ERC on startup)
> 

How do I know which driver is used? I did not change anything but delete the
RAID volume in the storage manager, even not reboot.

I tried again and set the five disks to five different values (disabled, 50,
60, 70 ... and so on). After creating the RAID volume every disk gives
37345. After deleting the volume again, all disks have their initially set
value, so I guess it's just a readout problem. Setting the scterc while in
RAID worked, too. After deleting the volume, the disk retained its set
value. It just seems not possible to get a valid result while in RAID.
Hopefully...

Remember that I made all tests while the Volume was initializing. I assume
the same results after initializing finishes but I couldnt test - it takes
about 24 hours...

I wonder if I should give it a try, just to see if the RAID will be
degrading or stable. 

Thanks,
 Fabian

--
View this message in context: http://smartmontools-support-list.2498698.n2.nabble.com/scteHD204UI-on-ICH10R-in-RAID5-tp6319996p6378238.html
Sent from the smartmontools support list mailing list archive at Nabble.com.

------------------------------------------------------------------------------
What Every C/C++ and Fortran developer Should Know!
Read this article and learn how Intel has extended the reach of its 
next-generation tools to help Windows* and Linux* C/C++ and Fortran 
developers boost performance applications - including clusters. 
http://p.sf.net/sfu/intel-dev2devmay
Permalink | Reply | 0 comments |

Gmane