ADS tech cardbus 1370

The dmesg that was sent is really  not correct. I changed the sudevice in saa7134-card.c to reflect 
what my eeprom reads. It was set to 0370.
My card appears to be of a different version then what I am seeing from
others. So what do I do to find the correct information. I do have this card
working with windows XP. Is there a file that I can read to get some 
information. This is the information from lspci -vv

0000:07:00.0 Multimedia controller: Philips Semiconductors SAA713X Audio+video 
broadcast decoder (rev f0)
        Subsystem: Ads Technologies Inc: Unknown device 1370
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin A routed to IRQ 169
        Region 0: Memory at 44000000 (32-bit, non-prefetchable) [disabled]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=3 PME-

--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request <at> redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list

Re: Is there hardware available to accelarate mpeg2 --> mpeg4 transcoding?

Alex Deucher wrote:
> Or perhaps you could write a
> fragment program in OpenGL to do the conversion and run it on your
> GPU.
>   

Is there such a beast out there?   I have not seen any programs.

--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request <at> redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list

Re: ADS Tech instant TV cardbus

Hi,

I installed the cvs snapshot today . Here is my dmesg after a modprobe
saa7134 card=58 tuner=54 :

saa7130/34: v4l2 driver version 0.2.14 loaded
ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [LNK4] -> GSI 11 (level,
low) -> IRQ 11
saa7133[0]: found at 0000:01:07.0, rev: 208, irq: 11, latency: 32,
mmio: 0xed010000
saa7133[0]: subsystem: 1421:0003, board: ADS Tech Instant TV (saa7135)
[card=58,insmod option]
saa7133[0]: board init: gpio is 40
saa7133[0]: i2c eeprom 00: 21 14 03 00 10 28 ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
tuner 0-004b: chip found  <at>  0x96 (saa7133[0])
tuner 0-004b: tuner: type set to tda8290+75
tuner 0-0061: chip found  <at>  0xc2 (saa7133[0])
saa7133[0]: registered device video0 [v4l2]
saa7133[0]: registered device vbi0

Unfortunetly I still have an almost black screen (a green noise at the
bottom of the screen 10 pixels height), but now, when I try to change
the frequency in xawtv or tvtime, I don't have any error message in

Re: ADS Tech instant TV cardbus

Me again ;)

I modprobe the card with 'modprobe saa7134 card=58 tuner=54
video_debug=1 and core_debug=1'

I have this line at the end of dmesg juste after the modprobe:
"saa7133[0]/video: DCSDT: pll: not locked, sync: no, norm: (no signal)"

I join the log when I try to change the channels in xawtv, maybe you
can decipher something ftom it.

Nicolas.

Oct  1 13:22:07 [kernel] saa7133[0]/core: buffer_queue ed764dc0
Oct  1 13:22:07 [kernel] saa7133[0]/core: buffer_finish ed764ec0
Oct  1 13:22:07 [kernel] saa7133[0]/core: buffer_next ed764dc0 [prev=ed764e24/next=ed764e24]
Oct  1 13:22:07 [kernel] saa7133[0]/video: buffer_activate buf=ed764dc0
Oct  1 13:22:07 [kernel] saa7133[0]/video: prescale=1 xscale=1920 yscale=1024
Oct  1 13:22:07 [kernel] saa7133[0]/video: yscale LPI yscale=1024
Oct  1 13:22:07 [kernel] saa7133[0]/core: dmabits: task=0x01 ctrl=0x01 irq=0x3 split=no
Oct  1 13:22:07 [kernel] saa7133[0]/core: buffer_next #2 prev=ed93b55c/next=ed93b55c
Oct  1 13:22:07 [kernel] saa7133[0]/video: buffer_prepare
[0,size=384x288,bytes=221184,fields=bottom,4:2:2 packed, YUYV]
Oct  1 13:22:07 [kernel] saa7133[0]/core: buffer_queue ed764ec0
Oct  1 13:22:07 [kernel] saa7133[0]/core: buffer_finish ed764dc0
Oct  1 13:22:07 [kernel] saa7133[0]/core: buffer_next ed764ec0 [prev=ed764f24/next=ed764f24]
Oct  1 13:22:07 [kernel] saa7133[0]/video: buffer_activate buf=ed764ec0
Oct  1 13:22:07 [kernel] saa7133[0]/video: prescale=1 xscale=1920 yscale=1024
Oct  1 13:22:07 [kernel] saa7133[0]/video: yscale LPI yscale=1024

tda8290/tda8275 - Was: A little help with ASUS TV FM CARD!

	Yes, most of the patch were already applied. The remaining parts are on
the enclosed patches. Please, try with the first, then unapply and apply
the second one.

Em Sex, 2005-09-30 às 11:36 -0700, &re escreveu:
> Mauro
> 
> It appears, that except for the low pass filter change, most of the 
> posted patch is already in the latest CVS. So I applied only the low 
> pass filter portions of the patch.  After doing so I lost tuning on half 
> of the channels (NTSC cable), so I must have missed something. Enclosed 
> is a diff of the low pass filter change against the latest CVS.
> Did I miss something ?

Cheers, 
Mauro.

--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request <at> redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list

cx88 module and DMA errors in syslog

Hello.

I have two nova-t dvb-t cards in my vdr computer. All working fine (ecxept 
singal cutting sometimes (between 20mins to 20hours). Can be allso antenna 
problem)
But now i need to ask is that normal that cx88 fills my syslog or not?
(sometimes (hours) all is fine and that message not coming to syslog but 
sometimes i got that message many hours couple times per second)

Oct  1 18:28:11 localhost kernel: cx88[1]/2: cx8802_restart_queue
Oct  1 18:28:11 localhost kernel: cx88[1]/2: cx8802_restart_queue: queue 
is empty
Oct  1 18:28:11 localhost kernel: cx88[1]/2: queue is empty - first active
Oct  1 18:28:11 localhost kernel: cx88[1]/2: cx8802_start_dma w: 0, h: 0, 
f: 2
Oct  1 18:28:11 localhost kernel: cx88[1]/2: setting the interrupt mask
Oct  1 18:28:11 localhost kernel: cx88[1]/2: [c7058ec0/0] cx8802_buf_queue 
- first active

Kernel version is 2.6.13.1 and v4l drivers from 
video4linux-20050922-030106.tar.gz snapshot.
(I have try to play whit PCI latency timers but whitout any result)

Tommi

--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request <at> redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list

GUVENLIK SISTEMLERINDE SON TEKNOLOJI

   İşyerinizi dünyanın herhangi bir yerinden  CANLI olarak izlemek ister misiniz?

Bu çok özel sistem ile; 
·	İstediğiniz yerden güvenlik sisteminize bilgisayarınızla bağlanarak mekanınızı canlı
olarak seyredebilirsiniz.
·	Aylarca mekanınızda personelinizin performansını müşteriye karşı tutumunu, müşteri
yoğunluğunu, satış trafiğini, istenmeyen hırsızlık, soygun, kapkaç vb. tüm
hareketlilikleri ve konuşmaları kayıpsız kontrol altına alabilirsiniz.
·	Seyretmek istediğiniz gün ve saatlerdeki kayıtlara anında ulaşabilir, üstelik kayıtları
uzaktan bağlanarak da seyredebilirsiniz.
·	Birden çok şubeniz var ise bütün şubelerinizi kayıt altına alabilir tek merkezden tüm
şubelerdeki kayıtları veya o anki canlı görüntüleri seyredebilirsiniz.
·	Sistemi profesyonel bir alarm sistemi olarak kullanabildiğiniz gibi mevcut alarm sisteminizle de
entegre edebilirsiniz.
            (Alarm anında kayıt, Fotoğraf çekme, Telefon aratma, sesli alarm vb. özellikler)
·	Bu sistem ile yapılan kayıtlar polis ve mahkemeler tarafından delil olarak kabul edilmektedir.
·	Bu sistem mevcut bulunan kameralarınızla uygulanabildiği gibi mevcut bilgisayarınızda da uygulanabilir.

Bu entegre sistem, konusunda en gelişmiş yazılım ve donanıma sahip olmakla beraber dünya
güvenlik sektörü için geliştirilen ilk ve tek video formatına da (SMICT Super Motion Image
Compression Technology) sahip olma özelliğini taşımaktadır.

            ilginize şimdiden teşekkür ederiz.

Saygılarımızla

FALİYET ALANLARIMIZ 

-Cctv Kapalı Devre Goruntu Yayını
-Görüntü Nakil Sistemleri  (internet üzerinden izlenim)

Voce recebeu um cartão!

--
video4linux-list mailing list
Unsubscribe mailto:video4linux-list-request <at> redhat.com?subject=unsubscribe
https://www.redhat.com/mailman/listinfo/video4linux-list

Re: tda8290/tda8275 - Was: A little help with ASUS TV FM CARD!

I applied both of the patches. Find enclosed the dmesg, scantv messages 
for the following 3 versions

1. current CVS of tuner.h & tda8290.c
2. cvs + tda_8290.cfix (39/3b)
3 cvs + tda8290.xfix_2 (29/2b)

To sum it up:
- I don't see a frequency offset in any of the versions.
- with the patches applied some channels can no longer be tuned to ( NTS 
cable channel 66,68 ...)

The general reception quality is the same with all 3 versions, the 
picture has lot's of noise & interferences. I added a 3db splitter to 
the line and the reception quality went from heavy interference to 
unusable picture, while a TV in parallel with the capture card showed 
only minor reception issues. It also appears that the tuner can't tune 
once in while, if I reboot without power cycling.

Does someone have the link to the tda8275/90 data sheet. I looked 
through the Phillips website but couldn't find it.

thx &re

----------------------------- dmsg 
--------------------------------------------------------------
saa7130/34: v4l2 driver version 0.2.14 loaded
ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 21 (level, low) -> IRQ 169
saa7133[0]: found at 0000:02:01.0, rev: 208, irq: 169, latency: 64, 

problems with WinFast TV 2000/XP: no signal

Hi,

I'm using a WinFast TV 2000/XP card with SuSE 9.3 on AMD64. I can't see any
video, tried with several programs. In tvtime I see a blue screen with "no
signal", and tvtime-scanner finds nothing. dmesg gives:

bttv: driver version 0.9.15 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
bttv0: Bt878 (rev 17) at 0000:01:09.0, irq: 225, latency: 32, mmio:
0xfeaff000
bttv0: detected: Leadtek TV 2000 XP [card=34], PCI subsystem ID is 107d:6609
bttv0: using: Leadtek WinFast 2000/ WinFast 2000 XP [card=34,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=003ff502 [init]
bttv0: using tuner=5
bttv0: i2c: checking for MSP34xx  <at>  0x80... not found
bttv0: i2c: checking for TDA9875  <at>  0xb0... not found
bttv0: i2c: checking for TDA7432  <at>  0x8a... not found
bttv0: i2c: checking for TDA9887  <at>  0x86... not found
tuner: chip found at addr 0xc2 i2c-bus bt878 #0 [sw]
tuner: type set to 5 (Philips PAL_BG (FI1216 and compatibles)) by bt878 #0
[sw]
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: registered device radio0
bttv0: PLL: 28636363 => 35468950 .. ok
bttv0: add subdevice "remote0"
bttv0: PLL can sleep, using XTAL (28636363).
bttv0: PLL: 28636363 => 35468950 .. ok
bttv0: timeout: drop=255 irq=7124/7124, risc=1e46a07c, bits: HSYNC OFLOW